Wheels - Cast Iron - AIE Company, inc.
Site Map Contact UsHome Page
 Toll Free Phone:  800-229-2431
Toll Free Fax:  888-993-3243

Local Phone:  770-263-6118  :  Local Fax:  770-242-0114
Email:  Info@AIECasters.com
 

Wheels - Cast Iron Wheels

Cast Iron (2-4 Series)

Colson

Cast Iron (2-4 Series)

Should be specified when excessive load weights are involved and floor protection is not a factor. High strength to withstand sharp impacts. Cast Iron wheels should not be used if noise is of major concern or if loads are fragile.

  • Temperature range: -45F to +180F. If metal washers specified: -45F to + 500F (Roller, Ball and Sleeve bearings only).
  • Finish: Green alkyd enamel.
view catalog 
   
Cast Iron (5-8 Series)

Colson

Cast Iron (5-8 Series)

Should be specified when excessive load weights are involved and floor protection is not a factor. High strength to withstand sharp impacts. They should not be used if noise is of major concern or if loads are fragile.

  • Temperature range: -45F to +180F. If metal washers specified: -45F to + 500F (Roller, Ball & Sleeve bearings only).
  • Finish: Green alkyd enamel.
  • Zerk Fitting: Zerk grease fitting in hub is standard on 7 and 8 Series wheels.
view catalog 
   
Albion CA Cast Iron Wheels

Albion

CA Cast Iron Wheels

Premium cast iron, sometimes referred to as semi-steel, offers the highest tensile strength in the industry (30,000 psi). A cost-effective solution for high capacity applications.

  • Wheel face: Machined flat with rounded edges
  • Finish: Gray enamel
  • Temperature Range: Up to 800F, consult factory
  • Hardness: Brinell 145
view catalog 
   
Albion CH Cast Iron Wheels

Albion

CH Cast Iron Wheels

Heavy duty premium cast iron, sometimes referred to as semi-steel, offers the highest tensile strength in the industry (30,000 psi). A cost-effective solution for high capacity applications.

  • Wheel face: Machined flat with rounded edges
  • Finish: Gray enamel
  • Temperature Range: Up to 800F, consult factory
  • Hardness: Brinell 145
view catalog 
   
Albion CW Cast Iron Wheels

Albion

CW Cast Iron Wheels

Large bore premium cast iron, sometimes referred to as semi-steel, offers the highest tensile strength in the industry (30,000 psi). A cost-effective solution for high capacity applications.

  • Wheel face: Machined flat with rounded edges
  • Finish: Gray enamel
  • Temperature Range: Up to 800F, consult factory
  • Hardness: Brinell 145
view catalog 
   
Hamilton Series M Cast Iron Wheels

Hamilton

Metal Wheels Series M - Cap. to 7,000 lbs.

With one of the industry's largest lines of metal wheels (most are cast iron, a few of the smaller sizes sintered iron), Hamilton has come to be known as the first place to go for new or replacement metal wheels. In the last three years, the most popular metal wheel sizes have been upgraded with larger hubs and less scrap metal content to represent the most durable and highest quality metal wheels in the industry.

  • Straight or Tapered Roller Bearing Seals.
  • Special Hub Length - hubs can be cut to provide shorter length, spacer washers furnished to increase length.
  • Keyways, and/or set screws - for locking wheels on shaft.
  • Spanner Bushings
view catalog 
   
Faultless Sintered Iron Wheels

Faultless

Sintered Iron - Capacity 150-450 Lbs. Each Wheel

Sintered Iron Powdered iron, compacted and sintered to cast-iron strength, makes a concentric and smooth tread. Standard with plain bearings. Temperature operating range is -40F to +500F.

view catalog